Honda CR-V: Heater Unit/Core Replacement

SRS components are located in this area. Review the SRS component locations, and the precautions and procedures before doing repairs or service.

1. Make sure you have anti-theft codes for the audio system and the navigation system (if equipped).

2. Make sure the ignition is OFF, then disconnect the negative cable from the battery.

3. Disconnect the A/C line from the evaporator core.

4. When the engine is cool, drain the engine coolant from the radiator.

5. From under the hood, slide the hose clamps (A) back. Disconnect the inlet heater hose (B) and the outlet heater hose (C) from the heater unit. Note the orientation of the hose.

Engine coolant will run out when the hoses are disconnected; drain it into a clean drip pan. Be sure not to let coolant spill on the electrical parts or the painted surfaces. If any coolant spills, rinse it off immediately.

Honda CR-V. HVAC (Heating, Ventilation, and Air Conditioning)

6. Remove the mounting nut from the heater unit.

Take care not to damage or bend the fuel lines or brake lines, etc.

Honda CR-V. HVAC (Heating, Ventilation, and Air Conditioning)

7. Remove the dashboard.

8. Disconnect the connector (A) from the blower motor. Remove the wire harness clip (B).

Honda CR-V. HVAC (Heating, Ventilation, and Air Conditioning)

9. Disconnect the connector (A) from the recirculation control motor.

Honda CR-V. HVAC (Heating, Ventilation, and Air Conditioning)

10. Disconnect the connectors (A) from the mode control motor, the evaporator temperature sensor, and the power transistor. Remove the wire harness clips (B).

Honda CR-V. HVAC (Heating, Ventilation, and Air Conditioning)

11. Disconnect the connectors (A) from the air mix control motor and A/C wire harness. Remove the connector clip (B), the wire harness clips (C), and the wire harness (D).

Honda CR-V. HVAC (Heating, Ventilation, and Air Conditioning)

12. Remove the clip (A) and the duct (B). Side the clamp, then remove the drain hose (C). Remove the mounting bolt, mounting nuts, and blower-heater unit (D).

Honda CR-V. HVAC (Heating, Ventilation, and Air Conditioning)

13. Remove the self-tapping screws and the driver's duct (A). Remove the self-tapping screws, the heater core cover (B), the grommet (C), and carefully pull out the heater core (D).

Honda CR-V. HVAC (Heating, Ventilation, and Air Conditioning)

14. Install the heater core and the evaporator core in the reverse order of removal.

15. Install the heater unit in the reverse order of removal, and note these items:

READ NEXT:

 A/C Compressor Replacement

NOTE: Do not install an A/C compressor into a system unless you are completely sure that the system is free of contamination. Installing the A/C compressor into a contaminated system can result in pre

 Receiver/Dryer Desiccant Replacement

NOTE: Install the receiver/dryer as quickly as possible to prevent the system from absorbing moisture from the air. 1. Remove the A/C condenser. 2. Remove the cap (A) from the bottom of the A/C cond

 Body Electrical

SEE MORE:

 Differential Disassembly

Special Tools Required Holder handle 07JAB-001020A Companion flange holder 07RAB-TB4010B 1. Remove the drain plug (A) and the oil filler plug (B) with sealing washers (C). 2. Raise the locknut tab (A) from the groove of the clutch guide, making sure the tab completely clears the groove to preve

 Removing Discs from the In-dash Disc Changer

To remove the disc currently in play, press the eject button. When a disc is removed from a slot, the system automatically begins the load sequence so you can load another disc in that position. If you do not remove the disc from the changer within 10 seconds, the disc will reload in

© 2016-2025 Copyright www.hcrv.net