Honda CR-V: Installing a Child Seat with LATCH
Your vehicle is equipped with LATCH (Lower Anchors and Tethers for CHildren) at the rear seats to secure a child seat in any seating position: one in each outer seating position, or one in the center.
The five lower anchors are located between the seat-back and seat bottom, and are to be used only with a child seat designed for use with LATCH.
The location of each lower anchor is indicated by a small button above the anchor point.
When you install a child seat in the rear center seating position, use the center lower anchors as shown in the illustration. To install a child seat in either outer seating position, use the outer lower anchors. You can install up to two child seats at a time using the outer lower anchors.
Do not attach two child seat connectors to a single lower anchor at a time.
Using the Outer LATCH
To install a LATCH-compatible child seat in either of the rear outer seats:
1. Store the seat belt buckle or tongue in the storage pockets.
2. Make sure there are no objects near the anchors that could prevent a secure connection between the child seat and the anchors.
3. Place the child seat on the vehicle seat, then attach the seat to the lower anchors according to the child seat maker’s instructions.
Some LATCH-compatible seats have a rigid-type connector as shown above.
Other LATCH-compatible seats have a flexible-type connector as shown above.
4. Whatever type you have, follow the child seat maker’s instructions for adjusting or tightening the fit.
5. If equipped
Remove the dual deck cargo shelf.
6. Route the tether strap over the seat-back and through the legs of the head restraint, then attach the tether strap hook to the anchor, making sure the tether strap is not twisted.
7. Tighten the strap according to the seat maker’s instructions.
8. Push and pull the child seat forward and from side-to-side to verify that it is secure.
9. Reinstall the dual deck cargo shelf.
Using the Center LATCH
To install a LATCH-compatible child seat in the rear center seating position, use the center lower anchors as shown above.
1. Follow step 1 through 5 as described previously to secure the child seat.
2. Pull down the cover to access the tether anchor.
3. Route the tether strap over the seat-back, then attach the tether strap hook to the tether anchor in the ceiling, making sure the strap is not twisted. Tighten the strap according to the seat maker’s instructions.
4. Push and pull the child seat forward and from side-to-side to verify that it is secure.
READ NEXT:
Installing a Child Seat with a Lap/Shoulder Belt
When not using the LATCH system,
all child seats must be secured to the
vehicle with the lap part of a lap/
shoulder belt.
In addition, the lap/shoulder belts in
all seating positions except
Installing a Child Seat with a Tether
A child seat with a tether can be
installed in any seating position in
the back seat.
Each rear outside seating position
has an anchorage point on the seatback,
and the center seating positio
Protecting Larger Children
When a child reaches the
recommended weight or height limit
for a forward-facing child seat, the
child should sit in a back seat on a
booster seat and wear the lap/
shoulder belt.
The follo
SEE MORE:
System Description
MICU Control Functions Index
The MICU (built into the under-dash fuse/relay box) is one of the B-CAN
components. The MICU controls many
systems related to the body controller area network, and also works as a gateway
to diagnose the other B-CAN circuits
with the HDS.
Refer to each system circuit d
Block and Piston Inspection
1. Remove the crankshaft and pistons.
2. Check the piston for distortion or cracks.
3. Measure the piston diameter at a point 13 mm
(0.5 in.) from the bottom of the skirt. There are two
standard-size pistons (No Letter or A, and B). The
letter is stamped on the top of the piston. Letters
are also
